Sold out
LabGruppen_IPD-2400-1
LabGruppen_IPD-2400-2
LabGruppen_IPD-2400-3
LabGruppen_IPD-2400-5
LabGruppen_IPD-2400-4
Load image into Gallery viewer, LabGruppen_IPD-2400-1
Load image into Gallery viewer, LabGruppen_IPD-2400-2
Load image into Gallery viewer, LabGruppen_IPD-2400-3
Load image into Gallery viewer, LabGruppen_IPD-2400-5
Load image into Gallery viewer, LabGruppen_IPD-2400-4
Take Control, at the Rack or AnywhereAll setup parameters for input mixing, DSP features and limiter setting are accessible on the front panel usin...

0.00

This item is currently sold out.
Take Control, at the Rack or Anywhere
All setup parameters for input mixing, DSP features and limiter setting are accessible on the front panel using two navigation buttons, a rotary encoder, and the backlit display. Individual channel mute buttons are also available. Up to 100 user-defined presets may be stored on-board.
Most users will also want to take advantage of the advanced, Ethernet-based networked monitoring and control features. Network configuration is fast and foolproof, with automatic discovery and identification of all connected amplifiers. The sleek GUI is designed for touch-based devices, and enables quick grouping of amplifiers along with intuitive setup and preset storage of all DSP parameters.
Exceptional I/O Flexibility
With AES3 digital inputs standard, IPD 2400 connects directly to digital console stage boxes, or accept AES input within a fixed digital network installation, eliminating a D-A/A-D conversion cycle. Additionally, AES3 inputs can be set for automatic fail-over to analog (perfect for keeping the show going, or in case of installations – maintaining system integrity for mission-critical PA/VA system applications), and input mixing is available for all four inputs. At the power output end, connections are available on binding posts or Neutrik speakON.
IntelliDrive Controller
At the heart of IPD Series is the intuitive GUI of the IntelliDrive Controller software, giving powerful user control over just about every aspect of DSP performance on each device on the network. Available on PC and Mac, and designed with touch-screen in mind, IntelliDrive Controller gives you the edge when it comes to system tuning.
 
Features Include:
General
Number of amplifier channels 2
Max total output all channels driven 2400 W
Peak output voltage per channel 70 Vrms
Max output current per channel 20 Arms
Max output power (all channels driven)
2 ohms 800 W
4 ohms 1200 W
8 ohms 600 W
16 ohms 300 W
Performance
THD 20 Hz - 20 kHz at 1 W <0.1%
THD at 1 kHz and 1 dB below clipping <0.05%
Signal to Noise Ratio >102 dBA
Channel separation (Crosstalk) at 1 kHz >80 dB
Frequency Response 2 Hz – 42 kHz
Input impedance 18 kOhm
Common Mode Rejection (CMR) 50 dB
Output impedance 25 mOhm
Gain, Sensitivity and Limiters
SCVPL 100 V peak
Sensitivity for full power 6 dBu
Gain (all DSP controls set to 0 dB) 33.2 dB
Level adjustment (per channel) Software controlled from -inf to 0 dB
Connectors and Buttons
Analog input connectors (per ch.) Neutrik XLR, 3pin female
Analog input link connectors (per ch.) Neutrik XLR, 3pin male
AES input connectors (per ch.) Neutrik XLR, 3pin female
AES input link connectors (per ch.) Neutrik XLR, 3pin male
Output connectors (per ch.) Neutrik speakON / binding post
Buttons Power, Menu, Back, Mute (per ch.), Power
Encoder Adjust / Set
Cooling Dual fan, front to rear airflow, no filter required, temperature controlled speed
Power
Nominal voltage 100 – 240 VAC
Operating voltage 60 – 265 V AC
Standby consumption <7.5 W
Mains connector IEC inlet
Dimensions
Dimensions (Rack rail to rear panel) W: 483 mm (19”), H: 44 mm (1 U), D: 359 mm (14.1”)
Dimensions (Overall incl. handles and rear support) W: 483 mm (19”), H: 44 mm (1 U), D: 431 mm (17”)
Finish
Finish Black anodized aluminum front and black / gray steel chassis

Related products

Recently viewed