Lab.Gruppen IPD 2400 Compact 2,400 Watt 2-Channel DSP Controlled Power Amplifier

Description

Take Control, at the Rack or Anywhere

All setup parameters for input mixing, DSP features and limiter setting are accessible on the front panel using two navigation buttons, a rotary encoder, and the backlit display. Individual channel mute buttons are also available. Up to 100 user-defined presets may be stored on-board.

Most users will also want to take advantage of the advanced, Ethernet-based networked monitoring and control features. Network configuration is fast and foolproof, with automatic discovery and identification of all connected amplifiers. The sleek GUI is designed for touch-based devices, and enables quick grouping of amplifiers along with intuitive setup and preset storage of all DSP parameters.

Exceptional I/O Flexibility

With AES3 digital inputs standard, IPD 2400 connects directly to digital console stage boxes, or accept AES input within a fixed digital network installation, eliminating a D-A/A-D conversion cycle. Additionally, AES3 inputs can be set for automatic fail-over to analog (perfect for keeping the show going, or in case of installations – maintaining system integrity for mission-critical PA/VA system applications), and input mixing is available for all four inputs. At the power output end, connections are available on binding posts or Neutrik speakON.

IntelliDrive Controller

At the heart of IPD Series is the intuitive GUI of the IntelliDrive Controller software, giving powerful user control over just about every aspect of DSP performance on each device on the network. Available on PC and Mac, and designed with touch-screen in mind, IntelliDrive Controller gives you the edge when it comes to system tuning.

Features Include:

General

Number of amplifier channels 2

Max total output all channels driven 2400 W

Peak output voltage per channel 70 Vrms

Max output current per channel 20 Arms

Max output power (all channels driven)

2 ohms 800 W

4 ohms 1200 W

8 ohms 600 W

16 ohms 300 W

Performance

THD 20 Hz – 20 kHz at 1 W <0.1%

THD at 1 kHz and 1 dB below clipping <0.05%

Signal to Noise Ratio >102 dBA

Channel separation (Crosstalk) at 1 kHz >80 dB

Frequency Response 2 Hz – 42 kHz

Input impedance 18 kOhm

Common Mode Rejection (CMR) 50 dB

Output impedance 25 mOhm

Gain, Sensitivity and Limiters

SCVPL 100 V peak

Sensitivity for full power 6 dBu

Gain (all DSP controls set to 0 dB) 33.2 dB

Level adjustment (per channel) Software controlled from -inf to 0 dB

Connectors and Buttons

Analog input connectors (per ch.) Neutrik XLR, 3pin female

Analog input link connectors (per ch.) Neutrik XLR, 3pin male

AES input connectors (per ch.) Neutrik XLR, 3pin female

AES input link connectors (per ch.) Neutrik XLR, 3pin male

Output connectors (per ch.) Neutrik speakON / binding post

Buttons Power, Menu, Back, Mute (per ch.), Power

Encoder Adjust / Set

Cooling Dual fan, front to rear airflow, no filter required, temperature controlled speed

Power

Nominal voltage 100 – 240 VAC

Operating voltage 60 – 265 V AC

Standby consumption <7.5 W

Mains connector IEC inlet

Dimensions

Dimensions (Rack rail to rear panel) W: 483 mm (19”), H: 44 mm (1 U), D: 359 mm (14.1”)

Dimensions (Overall incl. handles and rear support) W: 483 mm (19”), H: 44 mm (1 U), D: 431 mm (17”)

Finish

Finish Black anodized aluminum front and black / gray steel chassis

Additional information